• Recommended for use with all Createx Paints.
• 
  
• 4011 is a water-based thinner used to lower viscosity and promotes faster drying times and complete curing.
• 4011 is generally added 5% - 10% per volume to paint. For small tip-sized airbrush, add 4011 Reducer in greater amounts up to 20% per volume.
• 4011 is safer to use to over-reduce paint without seeding.
• 4011 assists drying times by flashing water from the paint. 4011 also helps reduce tip-dry compared to diluting with water.
• Water-based paint material containing Propylene Glycol Monomethyl Ether Acetate
• 
  
• Refer to 4011 Technical Data Sheet for more information about thinning and mixing specific color type

4013 Reducer is a thinner suitable for use with all Createx paints. 4013 Reducer can be used as substitute for 4011 Reducer.

• Recommended for use with all Createx Paints.
• 
  
• Assists drying times by flashing water from the paint
• Reduces tip-dry, and decreases paint viscosity *"thins it" for improved flow and atomization, especially when airbrushing.
• Generally added 5 - 10% per volume
• 4013 Reducer is compliant with clean air regulations and jurisdictions including South Coast AQMD Rule 1401.
• 
  
• Refer to: 4013 Technical Data Sheet for more information

• Recommended for use with all Createx Paints except AutoAir Autoborne Sealers
• 
  
• 4020 is a specialty additive, not to replace 4011 the standard dilutant for all Createx Colors paint.
• 4020 works best by mixing with 4011 to create a cocktailed dilutant. Diluting Createx paints with 4020 alone is not recommended as paint may prematurely cure, seed in the cup and create cured paint particle contaminants.
• Makes paint flow easy with minimal tip-dry.
• Mix ratios for adding 4020 to 4011 vary, but generally: • Airbrush: Mix 4011 1:1 4020 • Spray-gun: Mix 4011 3:1 4020
• Contains Acetone and Glycol Ethers. (flammable - can not ship via air)
  
  
• Use only in controlled spray environments with adequate ventilation and a NIOSH / MSHA approved respirator.
• 
  
• Refer to: 4020 Technical Data Sheet for more information
• 
  

• Recommended for use with all Createx Paints.
• 
  
• Rinses paint from airbrush or spray-gun more effectively compared to water when changing colors.
• Helps maintain proper working condition of airbrush or spray-gun by preventing build-up of dried paint.
• Spray 5618 in between colors while painting to partially clean airbrush or spray-gun before using next color.
• Compared to 4011, 5618 is a milder cleaner. When adding 4030 to Createx Colors paints and clears, flushing colors with 4011 is more effective compared to cleaning with 5618.
  
  
• Refer to: 5618 Technical Data Sheet for more information

• Recommended for use with all Createx Paints.
• 
  
• Partially dissolves dried paint allowing for easy clean-up with soap & water.
• Use as a soak for metallic parts: nozzle, needle, cup.
• Re-Usable. Keep in metal or ceramic container.
• Dissolves soft-plastics. Keep away from non-PTFE coated O-rings.
• Flush airbrush or spray-gun with water after using Restorer.
  
  
• Refer to: 4008 Technical Data Sheet for more information

• Recommended for use with all Createx Paints.


• Mix 4030 Balancing Clear 10 - 25% per volume or more with Createx Airbrush Colors for improved performance on non-porous, hard surfaces.
• 4030 mixed with Createx Airbrush Colors or any Createx Colors paint creates an acrylic-urethane paint which greatly improves spray performance.
• 4030 works as an adhesion promoter when mixed with Createx Airbrush Colors, perfect for painting plastics, vinyl and most any surface that is difficult for paint to adhere to.
• Createx Airbrush Colors air-dry to a much more durable coating when mixed with 4030 Balancing Clear.
• 4030 also works as a protective inter-coat when applied over Createx Airbrush Colors. Reduce 10% 4011 Reducer when applying 4030 as an inter-coat.
• 4030 appears milky in solution, dries clear. Colors dry to a satin finish when mixed with 4030.
• Mix with all Createx Colors prior to use when painting hard-surfaces, plastic & automotive.
• 
  
• See 4050 UVLS Clear Gloss for use as a balancing Cear with Pearls, Matalics and Flakes for increased viscosity, more durable product for hard-surface applicatin. (see the below video for more information)
  
• 
  
• See 4030 Technical Data Sheet for more information

• 4040 Bleed Checker is a hybridized, urethane-acrylic clear used as an inter-coat intended for application over candy2o to prevent the candy2o’s dyes from bleeding into top-coated colors.
  
  
• Apply 4040 Bleed Checker over candy2o as an inter-coat.  After 4040 has thoroughly dried (30 – 60 minutes), other colors including subsequent candy2o colors may be applied direct without scuffing.  4040 will prevent the underlying candy2o’s dye from leaching (“bleeding”) into the top-coated colors.
• 
  
• Apply 4040 Bleed Checker not reduced, straight from the bottle when applying as an inter-coat over candy2o.  Do not reduce with 4011 Reducer as it’s a solvent used with candy2o and use of it in 4040 will create a shared material between candy2o and 4040 which may allow for bleeding.
• 
  
• See 4040 Technical Data Sheet for more information

• Recommended for use with Wicked and AutoAir Paints Only.
• 
  
• 4004 works as a low-build inter-coat, transparent extender for Wicked and Auto Air colors. 4004 appears milky in solution yet dries clear.
• Works as a light, protective inter-coat perfect for protecting airbrushed artwork before taping. T-shirt painter may also wish to apply a light coat or two of 4004 onto the fabric prior to painting to lock down any fabric nap. Reduce 4004 Transparent Base 10% per volume with 4012.
• 
  
• See 4004 Technical Data Sheet for more information

• Recommended for use with all Createx paints.
• 
  
• Automotive-grade, Createx's most durable Transparent Base.
• Excellent adhesion promoter. Apply direct to any plastic for adhesion prior to applying colors.
  
• Self-levels & dries quickest of all Transparent Bases.
  
• Excellent adhesion promoter. Apply direct to any plastic for adhesion prior to applying colors.
  
• See 4004 Technical Data Sheet for more information

• Recommended for use with all Createx Products


• A versatile medium that can be added to any Createx paint.
• Slows the drying of paint, giving more time for blending or layering highlights.
• Helps reduce tip-dry compared to diluting with water
• Generally, this product is not required and not recommended in other than extreme conditions (i.e., xtremely hot conditions)
• When used in very small increments (1 - 2 drops per 4 oz of color) it can also enhance flow and help prevent paint drying in the tip of the airbrush. Mix thoroughly.

• Also works as an adhesion promoter for flexible plastics, leather, vinyl and more.
• Apply 2 medium coats direct to the surface, allow each coat to dry 10 – 15 minutes then apply paint.
• Avoid applying dry or overly wetter, adhesion is best applied as a medium coat.
• May also be mixed with colors and applied direct to the latex. 5092 is added about 25% per vol. to colors, which are then thinned 5% - 10% with 4011 Reducer.

• See Illustration Technical Data Sheet for more information

• 4008-04 Restorer
• 4011-04 4011 Reducer
• 4030-04 Balancing Clear

• Scenix High Performance SSR Clear is chemically resistant to acid rain, solvents & sunscreen (does not blacken or emulsify due to repeated exposure to sunscreen)


• Water-Based Aliphatic Acrylic
  
  
• Urethane Industrial Grade Coating for Exterior & Interior Application. ASTM E84 Class A Fire Rating for all Scenix Colors & Clears

Optional Accelerated Curing:
Adding 4016 Cross-Linker promotes a denser cross-linking of resin compared to air drying alone for accelerated cure times and maximized adhesion.
Add 4016 Cross-Linker at 2% per volume to paint. Stir thoroughly and allow to sit for 10 minutes acclimation before spraying or brushing.

• For use with SSR Clear over Hard Surfaces


• Recommended when painting hard substrates such as plastic, fiberglass, glass, aluminum and more.
• 
  
• When mixed with Cross-Linker, Scenix colors are very durable paints that have chemical resistance to acid rain, solvents and sunscreen (Scenix colors and clears do not "blacken" or emulsify from repeated exposure to sunscreen).
  
  
• Mix Ratio: 2% per volume
  2 oz 4015 to one gallon
  1/2 oz 4015 one Quart (32 oz)
  Mix thoroughly for several minutes and spray soon after mixing as mixture has a one-hour pot life.